Generac 5655 Liquid Cooled Standby Generator Maintenance Kit for 1.6L Engine

Generac 5655 Liquid Cooled Standby Generator Maintenance Kit for 1.6L Engine Review

Generac 5655 Liquid Cooled Standby Generator Maintenance Kit for 1.6L Engine Feature

• The Generac generator maintenance kit offers all the hardware necessary to perform a complete maintenance on Generac liquid-cooled generators
• Oil and coolant will need to be purchased separately based upon manufacturer recommendations
• Maintenance is recommended at every 200 hours or 2 years
• Includes air filter, oil filter, 4 spark plugs, spark plug wrench, oil funnel, chamois, and reminder sticker
• For 18-kilowatt low-speed, and 20-, 25-, and 30-kilowatt 3600-RPM 1.6-liter generators

Includes Air Filter, Oil Filter, (4) Spark Plugs, Spark Plug Wrench, Oil Funnel, Chamois, Reminder Sticker

Generac 6294 30-Amp 6-10 Circuit Manual Transfer Switch Kit for Portable Generators

Generac 6294 30-Amp 6-10 Circuit Manual Transfer Switch Kit for Portable Generators Review

Generac 6294 30-Amp 6-10 Circuit Manual Transfer Switch Kit for Portable Generators Feature

• Safely switch from utility to 30-amp portable generator power in an emergency and power critical circuits through your home?s electrical system
• Interchangeable type circuit breakers make it easy to reconfigure, replace, or expand the circuits in your switch
• Directly powers hard-wired appliances such as your furnace (gas/oil only), well pump, and septic pump
• Kit includes all components and suitable for surface mounting
• Comes with a 1-year limited warranty

The Generac 6294 30-Amp 6-10 Circuit Manual Transfer Switch Kit allows you to skip the hassle of running multiple extension cords from your generator to your appliances during a power outage. Instead, connect your Generac portable generator to a permanently installed Generac manual transfer switch. A Generac manual transfer switch allows you to safely switch from utility to portable generator power in an emergency and power critical circuits through your home’s electrical system. Use this transfer switch for 7,500-watt, 125/250-volt generators equipped with NEMA 3R L14-30 power outlets. The kit includes a 30-amp (6-10) circuit pre-wired transfer switch for surface mounting, a 10-foot 10/4 cord with L14-30 ends, wiring harness, conduit and fittings, wire connectors and installation manual. This item can be used with the GP5500, GP6500E, GO7500E, XG6500, XG7000E, XG8000E, XP6500E and XP8000E generators (XP units require a switch neutral kit). The mechanically interlocked generator and utility breakers prevent dangerous back feeding to avoid injuring utility line workers. This unit measures 9-1/4-inch wide, 11-1/8-inch high, 3-3/8-inch deep and weighs 19-pounds. The Generac 6294 30-Amp 6-10 Circuit Manual Transfer Switch Kit is backed by a 1-year limited warranty. Generac manufactures the widest range of power products in the marketplace including portable, RV, residential, commercial and industrial generators. Generac also operates three large factories that employ thousands of workers in the American Midwest.

Generac 0F7502 RV Generator Floor Mounting Tray Kit For QP40G, QP40LP

Generac 0F7502 RV Generator Floor Mounting Tray Kit For QP40G, QP40LP Review

Generac 0F7502 RV Generator Floor Mounting Tray Kit For QP40G, QP40LP Feature

• Designed for the QP40 RV Generator
• Allows gen to be mounted at floor level in a larger cutout area
• Compatibility: 4700, 4701, 4708, 4709, 5852, 5853

Quietpact 40 Floor Mount Kit � This mounting tray allows for the QP-40 gas or LP unit to be mounted at floor level in a larger cutout area.

Generac RV Generator Installation Kit For QP40G, QP40LP

Generac RV Generator Installation Kit For QP40G, QP40LP Review

Generac RV Generator Installation Kit For QP40G, QP40LP Feature

• Everything you need to install your RV generator
• Installation kit compatible with Generac QP-40 RV Generator Models: 4701, 4709, 5852, 5853
• Remote Start Panel with 30-foot Harness (0F0430) and 16-inch Run Tailpipe 1.25-inch O.D (0E0683)
• Remote Adapter Harness (connects to Onan remote) (0E1634A)
• Tail Pipe Hanger Bracket (0F2529)

Generac offers many different accessories to allow for easy installation and maintenance of your recreational vehicle generator. From scheduled maintenance kits to remote start / stop panels, Generac offers a full set of solutions. Includes remote start panel with 30 ft. harness, tailpipe with hanger, battery cable, remote adapter harness for connecting to an Onan remote, hanger bracket.

Briggs & Stratton Maintenance Minder Hour Meter 5081K

Briggs & Stratton Maintenance Minder Hour Meter 5081K Review

Briggs & Stratton Maintenance Minder Hour Meter 5081K Feature

• Maintenance Minder and Hour Meter
• Display Flashes every 25 Hours of Run Time
• For 2 and 4-Cycle Engines
• Genuine Briggs & Stratton Part

Briggs Stratton Small Engine Parts # 5081H HOURMETER-MAINT MNDR

GenTran 30 Amp 125-Volt Non-Metallic Generator Power Inlet Box NEMA L5-30

GenTran 30 Amp 125-Volt Non-Metallic Generator Power Inlet Box NEMA L5-30 Review

GenTran 30 Amp 125-Volt Non-Metallic Generator Power Inlet Box NEMA L5-30 Feature

• 30 Amp 125 volt non-metallic power inlet box for generators up to 3750 watts
• Durable, glass-filled nylon NEMA 3r-rated enclosure includes 30a 125v male inlet in NEMA configuration l5-30 on bottom
• High-impact, UV stabilized, glass-filled nylon resin
• Since generator connection is made on the bottom, these power inlet boxes retain the "rain tight" rating while in use
• A sloped top and posts on the back allow precipitation to drain off; UL listed

Use a power inlet box when you need to plug in your generator outdoors to connect to a transfer switch indoors. This non-metallic power inlet box is mounted on the exterior of a house or building, and your installer will run wire through the wall over to the transfer switch. Rated at 30-Amps @ 125-Volts for generators up to 3750-watt, this NEMA 3R-rated non-metallic enclosure is made from durable, glass-filled nylon and includes a 30-Amp 125-Volt male inlet in NEMA configuration L5-30 on bottom - so it retains a raintight rating when cord is connected, required by most inspectors. This model does not include a flip lid. For 125-Volt use only. UL Listed.

Champion Power Equipment No.C90015 Generator Cover for Champion 1200W-1500W Models

Champion Power Equipment No.C90015 Generator Cover for Champion 1200W-1500W Models Review

Champion Power Equipment No.C90015 Generator Cover for Champion 1200W-1500W Models Feature

• Made from durable, water repellent vinyl
• Specifically designed for champion generators to provided a custom fit
• Lightweight for easy coverage and movement
• Fits Champion Portable Generators from 1200-Watt to 1500-Watt sizes
• Note: do not operate generator while covered

Champion No.C90015 Generator Cover protects your Champion 1200-Watt to 1500-Watt Generator from the elements for storage or transporting. Made from durable, water resistant vinyl; the generator cover is specifically designed for a custom fit. Note: Cover is not to be used while generator is running. Cover dimensions are 18.9" (L) by 15.8" (W) by 14.2" (H). 90 Day Limited Warranty.

Generac 5662 Maintenance Kit for 8kW, 410cc Engine

Generac 5662 Maintenance Kit for 8kW, 410cc Engine Review

Generac 5662 Maintenance Kit for 8kW, 410cc Engine Feature

• Includes: air filter, oil filter, spark plug, spark plug wrench, oil funnel, chamois
• Oil must be purchased separately

Scheduled maintenance is a necessity for all standby generators. The Air Cooled Scheduled Maintenance kits offer all the hardware necessary to perform a complete maintenance on Generac air-cooled generators. Maintenance is recommended at every 200 hours or 2 years. If running in a dusty environment, more frequent maintenance may be required. Further maintenance details can be found in the generator owner's manual.

Sunforce 7 Amp Charge Controller

Sunforce 7 Amp Charge Controller Review

Sunforce 7 Amp Charge Controller Feature

• Protects battery from overcharge and discharge
• For use with 12 Volt solar panels and batteries only
• Handles up to 7 amps of array current and up to 105 watts of solar power
• Maintains 12V batteries in a fully charged state
• Operation: Yellow charging light indicates battery charging and green light indicates fully charged battery

The Sunforce 60012 7 Amp Charge Controller prevents overcharging and discharging of 12 Volt batteries. It is intended for use with 12 Volt solar panels and maintains 12 Volt batteries in a fully charged state. It can handle up to 7 amps of array current and up to 105 watts of solar power. The controller is easy to use with a yellow charging light that indicates that your battery is charging, and a green light that indicates a fully charged battery.

Key Component of a Solar System Over 15 Watts

A charge controller is a very important feature of a solar system and must be used on all systems over 15 Watts. A charge controller protects your batteries from overcharge and discharge. Charge controllers are the maintenance free protection of your solar panel and batteries.

A charge controller monitors the battery’s state-of-charge to insure that when the battery needs change-current, it gets it, and also insures the battery isn’t overcharged. Connecting a solar panel to a battery without a regulator seriously risks damaging the battery and potentially causing a safety concern.

Charge controllers are rated based on the amount of amperage they can process from a solar array.

The Sunforce 60012 7 Amp Charge Controller prevents overcharging and discharging of 12 Volt batteries. It is intended for use with 12 Volt solar panels and maintains 12 Volt batteries in a fully charged state. It can handle up to 7 amps of array current and up to 105 watts of solar power. The controller is easy to use with a yellow charging light that indicates that your battery is charging, and a green light that indicates a fully charged battery.

GenTran RJB10310 10-Foot 30 Amp Power Cord for up to 3,750-Watt Generators

GenTran RJB10310 10-Foot 30 Amp Power Cord for up to 3,750-Watt Generators Review

GenTran RJB10310 10-Foot 30 Amp Power Cord for up to 3,750-Watt Generators Feature

• 10-foot 30 Amp generator cord connects generator to transfer switch or power inlet box
• Heavy-duty cord for durability; stays flexible in sub-zero temperatures
• Made from all rubber
• Includes male and female 3-wire twist-lock ends in NEMA configuration L5-30
• For up to 3,750-watt generator

The GenTran 10-foot 30 Amp generator cord for up to 3,750-watt generator connects your generator to your transfer switch or power inlet box. Made from all rubber, this heavy duty cord lasts forever, staying flexible even in sub-zero temperatures. It includes male and female 3-wire twist-lock ends in NEMA configuration L5-30. The male plug goes to the generator, and the female connects to transfer switch or power inlet box.

Coleman Cable 026198802 20-Amp Generator Cord 5-20P to 5-20R, Lighted, 100-Feet

Coleman Cable 026198802 20-Amp Generator Cord 5-20P to 5-20R, Lighted, 100-Feet Review

Coleman Cable 026198802 20-Amp Generator Cord 5-20P to 5-20R, Lighted, 100-Feet Feature

• Works with most generators
• All-purpose, portable outdoor cord stays flexible under extreme temperatures
• Outer jacket is flame retardant and water resistant
• Standard power indicator light in the receptacle to show power is on
• Perfect for workshops and jobsites

Generator Extension Cords

GenTran 20 Amp 125/250-Volt Non-Metallic Generator Power Inlet Box NEMA L14-20

GenTran 20 Amp 125/250-Volt Non-Metallic Generator Power Inlet Box NEMA L14-20 Review

GenTran 20 Amp 125/250-Volt Non-Metallic Generator Power Inlet Box NEMA L14-20 Feature

• 20 Amp non-metallic power inlet box, UL listed for generators up to 5000 watts
• Durable, glass-filled nylon NEMA 3r-rated enclosure includes 20a 120/240v male inlet in NEMA configuration l14-20 on bottom
• A sloped top and posts on the back allow precipitation to drain off
• Since generator connection is made on the bottom, these power inlet boxes retain the "rain tight" rating while in use
• 99-Inches of wiring room and 6 knockouts provide ultimate wiring flexibility

Use a power inlet box when you need to plug in your generator outdoors to connect to a transfer switch indoors. This non-metallic power inlet box is mounted on the exterior of a house or building, and your installer will run wire through the wall over to the transfer switch. Rated at 20-Amps for generators up to 5000-watt, this NEMA 3R-rated non-metallic enclosure is made from durable, glass-filled nylon and includes a 20-Amp 125/250-Volt male inlet in NEMA configuration L14-20 on bottom - so it retains a raintight rating when cord is connected, required by most inspectors. Works with any transfer switch rated at 20-Amps. This model does not include a flip lid. UL Listed

DEWALT DW087K LaserChalkLine Self-Leveling Line Laser, Horizontal & Vertical

DEWALT DW087K LaserChalkLine Self-Leveling Line Laser, Horizontal & Vertical Review

DEWALT DW087K LaserChalkLine Self-Leveling Line Laser, Horizontal & Vertical Feature

• Easy, one-button operation
• Accurate to 1/8-inch at 30 feet
• Magnetic pivot bracket built in for easy mounting on metal surfaces
• Features an out-of-level flashing indicator that kicks into gear when out of level
• Three AA batteries included for increased 20 hours of run time

With the DEWALT DW087K Self-Leveling Line Laser, you get accurate measurements essential to all construction and remodeling projects. This self-leveling line laser can be used for both horizontal and vertical applications and gives precise readings even at long distances.

Self-Leveling Line Laser At a Glance: Self-leveling within 5 degrees Accurate to within 1/8 inch at 30 feet Easy one-button operation Indoor visibility range of 50 feet Three-year limited warranty, one-year free service, 90-day money-back guarantee

This precise line laser lets you take on complex projects with confidence. View larger.

Features one-button operation and a magnetic pivot bracket.

Delivering the Accuracy You Need
Whether you're lining up lighting fixtures or flooring, the DEWALT Self-Leveling Line Laser eliminates the need for clumsy chalk lines or time-consuming calculations. This efficient tool offers self-leveling within 5 degrees, allowing for a quick, easy, and reliable measurement. Plus it is accurate to within 1/8 inch at a distance of 30 feet.

Convenient, Durable Design with Magnetic Bracket
Built for easy use, the DW087K offers one-button operation--no complicated menus to worry about. It also features a built-in, magnetic pivot bracket that allows the level to be mounted quickly and easily on metal surfaces. And, when working indoors, the level's red laser line is visible at a distance of 50 feet.

A set of three AA batteries can supply over 20 hours of run time, so battery changes are few and far between.

Durable Housing and Protective Kit Box
The DW087K's over-molded housing helps maintain calibration under tough job-site conditions, and the sturdy kit box protects the laser between uses.

The DW087K Self-Leveling Line Laser comes with a DEWALT warranty package that includes a three-year limited warranty, a one-year free service contract, and a 90-day money-back guarantee.

What's in the Box
DW087K Self-Leveling Line Laser, three AA batteries, and kit box.

Use the Line Laser to measure acoustical drop ceilings.

Make fast work of steel framing projects.

Install cabinets with confidence and precision.

Take on chair rail installation and other detailed finishing projects.

Powertronics 100 Foot 30 Amp L14-30 Generator Power Cord for up to 7,500 Watt Generators (10/4)

Powertronics 100 Foot 30 Amp L14-30 Generator Power Cord for up to 7,500 Watt Generators (10/4) Review

Powertronics 100 Foot 30 Amp L14-30 Generator Power Cord for up to 7,500 Watt Generators (10/4) Feature

• NEMA L14-30 L1430 Plug and Receptacle connectors
• 100 foot long Generator power cord for up to 7500 Watt Generators
• L14-30 Socket on one end, L14-30 Plug on the other
• 10 Gage, Rubber Coated 4 conductor stranded copper cord for full loads.
• Excellent flexibility even in cold weather (rated to -40 deg C (and -40 F)

10 foot long 100nerator power cord for up to 7500 Watts uses L14-30 Socket on one end, L14-30 Plug on the other. Cord Cable feature stranded bare copper conductor, separator, CPE Rubber or EPR insulation, suitable fillers, separator and CPE jacket. Cord has a temperature range of -40°C to + 60°C. Cord is designed for use in portable tools and equipment. Cord may also be used for portable appliances, small motors and associated machinery. Cord features excellent resistance to oil and moisture, good tensile strength, elongation and aging characteristics, high flexibility, excellent abrasion resistance.